Skip to content

Troubleshooting

Position reads “Geo Marker needs your location to show your grid.” Location is off for Geo Marker. Tap Open Settings, then Location, and choose While Using the App with Precise Location on.

It stays on “Finding your position…”. The phone has no fix yet. Step outside with a clear view of the sky. It needs no signal.

The bar reads “approximate” and the grid is far off. Precise Location is off. Geo Marker’s Settings show it as Precise Location: Off. Turn it on in the iPhone’s Settings ▸ Apps ▸ Geo Marker ▸ Location.

The bar reads “indoors?”. The phone is placing itself from Wi-Fi or cell towers, not satellites. Go outside.

The bar reads “poor”. The ± is 20 m or worse: trees, a ravine, buildings. Move to open ground, stand still and give it a few seconds.

The bar reads “GPS lost”. No position is coming in. The screens show the last one. It recovers by itself when the sky is visible again.

The grid panel says MGRS near the poles is not supported. You are beyond 84° north or 80° south, where MGRS uses a different grid that this app does not have. Use the latitude and longitude row.

Altitude reads “GPS, rough” or “No height yet”. The phone has no GPS height within 8 m. Read the ± beside it, or wait in the open. See Accuracy.

A typed mark is in the wrong place. Check, in this order:

  1. The zone and square in the box on the left of the keypad. It is filled from where you stand, so a grid from another 100 km square needs it changed.
  2. Easting first, then northing: right, then up.
  3. The number of digits. Eight digits typed into a 6-digit field stop after six.

The line beside the folder menu shows the distance and azimuth from you while you type. If it reads 90 km when you expected 900 m, a digit or the square is wrong.

The mark is a few tens of meters from where I expected. A grid names the southwest corner of its square, not the middle. A 6-digit grid is a 100 m square.

The grid is about 200 m off my paper map. Look at the datum in the map’s margin. Geo Marker is on WGS 84; an older map on NAD 27 has its grid about 200 meters away. See Accuracy.

Save is gray in New mark. The sheet has no position yet: the grid is not complete, the phone has no fix for Here, or Project is missing its distance or azimuth.

“That is not a zone and square”. Type a zone from 1 to 60, its band letter and the two square letters, like 18T WL.

I made a folder and cannot see it. A folder is listed once it holds a mark. It is in the folder menus already: move a mark into it.

I deleted a mark by mistake. Open Settings ▸ Recently Deleted and tap Restore.

The azimuth disagrees with my hand compass. They are probably from different norths. Look at the word after the azimuth: grid, magnetic or true. A hand compass reads magnetic. Switch Azimuths from in Settings, or convert with Tools ▸ Grid, magnetic, true.

I chose magnetic north and azimuths still say “true”. The phone does not know the declination yet. Open Position and hold the phone flat for a moment with a fix, so the compass runs once.

The heading card reads “No compass”, or Go To says the arrow assumes north. The compass has no usable reading. Hold the phone flat and move away from metal. The distance and azimuth on Go To are still right; walk them with a hand compass.

The arrow points the wrong way. Hold the phone flat with its top ahead of you, away from metal. Check the heading on Position against a hand compass, with Azimuths from set to Magnetic north.

The arrow turned into a still mark. You are inside the mark’s circle: You’re there.

“You’re there” came up early. The circle is 15 m, and up to 25 m when the fix is loose. Look at the ± on the bar.

Off the line shows a dash. The leg has no start yet (no fix when it began), or you are beyond the UTM grid’s limits.

“This needs at least two marks.” Resection and intersection work from marks. Add the known points on Marks first.

“Those lines do not cross in front of the marks.” The azimuths describe no place. Check each number, check its row, and check the unit and north named under the rows. With Magnetic north chosen and no declination yet, there is no answer either: let the compass run once, or switch to grid north.

Resection shows two answers. The marks are near a grid zone edge. Tap My map is in zone … for the zone printed in your map’s margin. See Resection.

Sight is gray. The phone has no compass reading. Type the azimuth from a hand compass.

The pace walk has no save button. Walk at least 50 m from where you tapped Start.

The map is blank and only the grid shows. The map’s pictures need a connection. The grid, your marks, the crosshair and the ruler still work. See With no signal.

There are no grid lines. Turn on the grid button on the map. If it is on, zoom in: the lines are not drawn when the map spans more than about 14°, or beyond 84° north and 80° south.

“No marks found in that file.” The file holds no waypoints, placemarks or points. A GPX with only a track has none. A KMZ must be unzipped to KML first. See Import and export.

Imported marks are all circles. Symbols are kept only when they are Geo Marker’s own.

My marks are not on my other device. Check Settings ▸ iCloud on both: Sync with iCloud on, and Now reading Syncing with iCloud. A change to the switch takes effect the next time the app starts. Both devices must be signed in to the same Apple Account.

Still stuck? Write to us.